banner

Soldering method to PCB assembly IC

For ICs with many leads, care must be taken during the soldering process to avoid sticking and misalignment of the IC leads. Repeated operation will cause the chip to damage the pads off. Therefore, it must be done carefully and carefully during the soldering process.

The following steps is shared by the PCBA production line technicians on welding IC method :

1,The method of cleaning and fixing the printed circuit board is the same as the two-terminal component.

2,Select the tin on the pad at the edge of the most edge on the IC lead pattern.

3,Clamp the IC with tweezers and place it on the lead diagram of the IC on the printed circuit board. The alignment position is fixed. Then, the soldering iron is used to heat the solder on the pre-solder pad until the solder melts and the lead is soldered. until. The position of the IC can be properly adjusted during the soldering process,then remove the soldering iron .

pcb assembly

Note: Do not touch the IC at this time. Do not move after fixing the IC with tweezers. Otherwise, the lead wires of the components may be misaligned and the welding may fail.

4,Check the alignment of the leads. All the leads of the IC need to be aligned with the pads on the lead pattern. If they are not aligned, they need to be re-soldered to align them.

After the leads are aligned, the leads of the soldered leads are soldered at the diagonal position, so as to avoid the misalignment of the leads caused by the movement of the IC when soldering other leads.

Soldering other leads, you need to use a magnifying glass, preferably a table lamp with a magnifying glass. Because it requires two-hand operation when soldering, use a pointed soldering iron to solder the leads of the IC one by one.

Check the lead wire soldering condition with a magnifying glass.The method of handling the feet: Because the IC leads are dense, it is inevitable that the two leads are connected together during soldering, and then it needs to be treated with a tin strip. The specific operation is to place the soldering strip on the soldering position, and heat it on the soldering strip with the soldering iron until the solder is melted and sucked away by the soldering strip, and the soldered leads are separated, and then the soldered leads are proceed to Welding operation.

Note: In this PCB assembly process, the action should be light, avoiding bending the IC leads, causing the leads to be misaligned or the leads to be broken.

If a lot of leads are accidentally soldered together, a tin strip can be used for suction and then repaired.

Check the solder joint again with a magnifying glass to ensure that the solder joint is qualified and there is no sticking and short circuit.

Note: Wear an anti-static wrist strap when performing PCB assembly and soldering IC to avoid static damage ring IC during soldering. For more information on the electronics industry, please pay attention to our status.

 

PCB board short circuit six inspection methods

PCB board short circuit six inspection methods First, opening the PCB  board design on the comput...

Do you like ? 777

Read more
Common PCB circuit board fault detection method

Common PCB circuit board fault detection method   Common PCB circuit board faults are mainly...

Do you like ? 1,129

Read more
During circuit board soldering process, what should be paid attention to?

During circuit board soldering process, what should be paid attention to? 1. Possible conditions...

Do you like ? 1,553

Read more
What do the “special pads” on the PCB do?

What do the “special pads” on the PCB do? First, the plum pad 1, The fixing hole need...

Do you like ? 778

Read more
What are the requirements and specifications for pwb positioning holes?

What are the requirements and specifications for pwb positioning holes? What is a PCB positioning...

Do you like ? 683

Read more
Circuit board spray tin  function and technics procedure introduction

Circuit board spray tin  function and technics procedure introduction The so-called spray tin is ...

Do you like ? 687

Read more
Surface Mount Technology (SMT)

Surface Mount Technology (SMT) Surface Mount Technology (SMT), also known as surface assembly tec...

Do you like ? 771

Read more
How to wash the pcba

How to wash the pcba After the PCBA processing process is completed, it is often seen that there ...

Do you like ? 720

Read more